Why Choose CHEMetrics Chemets kits?
CHEMetrics Chemets self-filing reagent ampoules are a great way to test for dissolved substances in liquids. These visual test kits allow you to obtain results by measuring the color of the sample according to the color comparators provided with the kit. This unique method allows you to attain results quickly and accurately with minimal contact with potentially hazardous materials.
Safe and Reliable Results:
While traditional methods often require multiple steps and thorough preparation, these test kits allow you to obtain dependable results with a few simple steps. By simplifying the testing method, Chemets test kits reduce the potential for operator error. Additionally, each of the ampoules contained in the test kits is vacuum sealed which helps eliminate the problem of obtaining inaccurate results from stale or unstable reagents. These reagents are stored right in the tip of each ampoule and sealed in glass, thereby minimizing direct contact with the chemicals.
-30 self-filling Ampoules
-low and high-range comparators
-1 25 mL Sample Cup
-1 mL syringe
The K-1510 Ammonia Kit was designed to accurately measure the levels of Ammonia in water from 0-1 ppm and 1-10 ppm. K-1510 uses the Direct Nesslerization Method. The test kits employing the well-established Nessler reagent* to determine ammonia concentrations are applicable to drinking water, clean surface water, good-quality nitrified wastewater effluent, and seawater. In some waters, calcium and magnesium concentrations can cause cloudiness of the reagent. Adding a few drops of stabilizer solution (Rochelle Salt) will prevent this cloudiness. References recommend distilling samples prior to analysis. Results are expressed as ppm (mg/L) ammonia-nitrogen, NH3-N.
Shelf-life: Although the Nessler reagent is stable, its high alkali content attacks the glass ampoule. The resulting precipitate interferes with color comparison. We recommend stocking quantities of CHEMets® and VACUettes® ampoules that will be used within five months. A two-month supply of Vacu-vials ampoules is suggested. Refrigeration will dramatically extend the shelf-life of these products.
|1. Fill the sample cup to the 25 mL mark with the sample to be tested. Add 2 drops of Stabilizer Solution. Stir to mix the contents of the cup.||2. Place the ampoule tip-first into the sample cup. Snap the tip and the ampoule will automatically fill.|
|3. To mix the ampoule, tilt it from side to side, allowing the bubble to travel from end to end.||4. Dry the ampoule and wait 1 minute for color development.|
|5. Place the ampoule into the center of the round comparator and hold it toward a source of light, viewing from the bottom. Rotate the comparator until the color below the ampoule shows the closest match.||6. For higher concentrations, use flat comparator. Place the ampoule between the color standards, moving it along the comparator until you can determine the closest match.|
For more detailed instructions, see the link at the bottom of the page.
WARNING! This product can expose you to chemicals including mercury, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
More CHEMetrics Kits for Ammonia:
|K1413||Hydroxybenzyl Alcohol (HBA)||0-3.00 & 0-60.0ppm|
|K1510||Direct Nesslerization||0.05ppm||0-1 & 1-10ppm|
|K1420||Hydroxybenzyl Alcohol (HBA)||0.125ppm||0-4 & 0-80ppm|
|K1510A||Direct Nesslerization||10ppm||0-50 & 60-600ppm|
|K1510B||Direct Nesslerization||20ppm||0-120 & 120-1200ppm|
|K1510C||Direct Nesslerization||100ppm||0-1000 & 1000-10,000ppm|
|K1510D||Direct Nesslerization||5ppm||0-30 & 30-300ppm|
|K1420B||Hydroxybenzyl Alcohol(HBA)||30ppm||0-500 & 0-10,000ppm|
|K1420D||Hydroxybenzyl Alcohol(HBA)||8ppm||0-125 & 0-2,500ppm|
Downloads and Links:
|Quickbooks Stock Level||0.000000|
|Call For Price||No|
|4-20 mA Output||No|
|Power Requirements||4 AAA Batteries|
|Range||0-1 ppm, 0-10 ppm|